Doing your own work on your Jimny? Getting the torque right is one of the most important steps.
We've painstakingly gone through the OEM Suzuki Jimny factory service workshop manual and pulled out every tightening torque it lists, then sorted them by system so you can find what you need quickly. All figures are in Newton metres (Nm), exactly as listed in the manual.
We made sure to add the factory service manual reference pages for every category, meaning if you'd like to cross reference our work - you can easily find them in the factory manual by following those numbers. We've even put the tightening diagrams as well for parts that have it.
Use the search box to find a bolt, or open a section below.
Wheels
Source: Ch. 1 Emergency actions (1•2)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Wheel nuts | 88 | Tighten alternately in the sequence shown (1–5) in more than two steps. Re-tighten after 1,000 km, including after replacing a damaged wheel.
Show tightening order |
Engine – mechanical
Source: Ch. 6 Mechanical engine, appendix (6•88)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Throttle body bolt | 11 | – |
| Throttle body nut | 11 | – |
| Cylinder head cover bolt | 3.0 → 5.0 → 7.5 | Staged tightening: tighten in the steps shown, in the sequence shown.
Show tightening order |
| Engine wiring harness cover bolt | 10 | – |
| Intake camshaft phaser (VVT) bolt | 60 | – |
| Camshaft cover (housing) bolt | 5.0 → 8.0 → 11 | Staged tightening: tighten in the steps shown, in the sequence shown.
Show tightening order |
| Exhaust camshaft sprocket bolt | 60 | – |
| Timing chain cover plug | 25 | – |
| Crankshaft pulley bolt | 19 + 75° | Torque to 19 Nm, then turn a further 75°. |
| Engine wiring harness mounting bracket bolt | 10 | – |
| Timing chain cover No. 1 bolt | 25 | Tighten in the sequence shown.
Show tightening order |
| Timing chain cover No. 2 bolt | 25 | Tighten in the sequence shown.
Show tightening order |
| Phaser oil control valve bolt | 11 | – |
| Flywheel bolt | 76 | – |
| Drive plate bolt | 69 | – |
| Timing chain damper (guide) bolt | 11 | – |
| Timing chain tensioner lever bolt | 25 | – |
| Timing chain tensioner bolt | 11 | – |
| Cylinder head bolt | 20 → 40 → +60° → +60° | Staged: 20 Nm, 40 Nm, then two further 60° turns. Tighten in the sequence shown.
Show tightening order |
| Venturi plug | 3.5 | – |
| Connecting rod cap bolt | 15 + 65° | Torque to 15 Nm, then turn a further 65°. |
| Sensor plate fixing screw | 11 | – |
| Main bearing cap (crankshaft support) bolt | 20 → 40 → +60° | Staged: 20 Nm, 40 Nm, then a further 60° turn. Tighten in the sequence shown.
Show tightening order |
| Crankshaft oil seal housing bolt | 11 | – |
Fuel & engine control
Source: Ch. 7 Power supply & engine control (7•92 – 7•101)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Fuel tank mounting bolts | 40 | – |
| Fuel rail mounting bolts | 25 | – |
| Coolant temperature sensor | 12 | – |
| Oxygen sensor | 45 | – |
| Crankshaft position sensor bolt | 11 | Apply fresh engine oil to the sensor O-ring. |
| Knock sensor mounting bolt | 23 | – |
Cooling system
Source: Ch. 8 Cooling system, appendix (8•112)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Radiator drain plug | 2.5 | – |
| Thermostat cover bolt | 25 | – |
| Cooling fan bolt | 7.0 | – |
| Fan motor mounting bolt | 4.0 | – |
| Radiator mounting bolt | 11 | – |
| Water pump mounting bolt | 25 | – |
| Water pump mounting nut | 25 | – |
| Water pump pulley bolt | 20 | – |
Lubrication system
Source: Ch. 9 Lubrication system, appendix (9•122)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Oil pan drain plug | 35 | – |
| Oil filter | 14 | – |
| Oil pressure switch | 13 | – |
| Oil filter stand (union) | 18 | – |
| Oil baffle plate stud | 11 | – |
| Oil baffle plate bolt | 11 | – |
| Oil strainer (pickup) bolt | 11 | – |
| Oil strainer (pickup) nut | 11 | – |
| Oil pan bolt No. 1 | 11 | Tighten in the sequence shown.
Show tightening order |
| Oil pan bolt No. 2 | 11 | Tighten in the sequence shown.
Show tightening order |
| Transmission-to-engine bolt | 55 | – |
| Water pump belt cover bolt | 11 | – |
| Oil pressure relief valve retainer | 28 | Apply fresh engine oil to the valve and spring before fitting. |
| Oil pump cover bolt | 11 | – |
Intake & exhaust
Source: Ch. 10 Intake & exhaust system, appendix (10•129)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Exhaust manifold mounting bolt | 60 | Use a new gasket. Tighten bolts and nuts in the sequence shown.
Show tightening order |
| Exhaust manifold mounting nut | 60 | Tighten in the sequence shown.
Show tightening order |
| Exhaust manifold strut nut | 25 | Fit the nut by hand first, tighten the strut bolt, then tighten the nut. |
| Exhaust manifold strut bolt | 25 | – |
Clutch
Source: Ch. 11A Clutch, appendix (11A•138)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Clutch pedal position sensor lock nut | 7.5 | – |
| Clutch release bleeder valve plug | 8.5 | – |
| Clutch master cylinder nut | 23 | – |
| Clutch slave (working) cylinder bolt | 23 | – |
| Clutch cover (pressure plate) bolt | 5.0 → 23 | Tighten alternately in several passes, in the sequence shown.
Show tightening order |
| Clutch cover mounting bolt (alternative version) | 23 | – |
Manual gearbox & differentials
Source: Ch. 11B Manual transmission, appendix (11B•165)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Level/filler plug | 21 | – |
| Drain plug | 23 | – |
| Level/filler plug | 23 | – |
| Reverse lamp switch | 19 | – |
| Transmission case bolt | 23 | – |
| Reverse idler gear shaft bolt | 23 | – |
| Transfer shift rod clamp bolt | 13 | – |
| Extension housing bolt | 23 | – |
| Case bolt | 23 | – |
| Gear shift mechanism bolt | 50 | – |
| Front diff drain plug | 55 | – |
| Front diff carrier-to-axle bolt | 30 | – |
| Vacuum nozzle mounting bracket bolt | 9.0 | – |
| Front diff ring gear (driven gear) bolt | 85 | – |
| Front diff flange nut | 100 – 400 | – |
| Front diff bearing cap bolt | 1.5 | – |
| Front diff bearing cap bolt | 50 | – |
| Front diff lock plate bolt | 12 | – |
| Rear diff level/filler plug | 50 | – |
| Rear diff drain plug | 55 | – |
| Rear diff carrier-to-axle bolt | 30 | – |
| Rear diff ring gear (driven gear) bolt | 90 | – |
| Rear diff flange nut | 100 – 400 | – |
| Rear diff bearing cap bolt | 1.5 | – |
| Rear diff bearing cap bolt | 85 | – |
| Rear diff lock plate bolt | 12 | – |
Automatic transmission
Source: Ch. 11C Automatic transmission, appendix (11C•178)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Fluid pressure test service port plug | 7.4 | – |
| ATF drain plug | 17 | – |
| Selector (mode select) nut | 13 | – |
| Selector handle screw | 3.0 | – |
| Selector rod nut | 13 | – |
| Transmission range sensor bolt | 13 | – |
| Output shaft speed sensor bolt | 5.5 | – |
| Input shaft speed sensor bolt | 5.5 | – |
| Transmission solenoid valve bolt | 6.5 | – |
| Control valve body case bolt | 11 | – |
| Oil strainer mounting bolt | 9.8 | – |
| Oil pan bolt | 5.2 | – |
| Valve body electrical connector plate bolt | 5.5 | – |
| Torque converter mounting bolt | 25 | – |
| Oil pump mounting bolt | 12 | – |
| Torque converter housing bolt | 25 | – |
| Manual shift lever spring bolt | 15 | – |
| P-position lock plate bracket bolt | 8.0 | – |
| Valve body bolt | 13 | – |
| Extension housing bolt | 25 | – |
| Range sensor nut | 6.9 | – |
| Manual selector lever nut | 13 | – |
| ATF cooler pipe bolt | 6.0 | – |
| Connecting (union) bolt | 28.0 | – |
| Oil pump housing bolt | 10 | Stator shaft to oil pump housing: 11 bolts. |
Front & rear axles
Source: Ch. 12 Drive shafts & transfer box (12•182 – 12•200)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Front wheel bearing lock nut | 216 | – |
| Front wheel hub bolt | 50 | – |
| Spindle bolt | 50 | – |
| Kingpin bolt | 25 | – |
| Steering knuckle seal cover bolt | 10 | – |
| Rear brake backing plate nut | 27 | – |
| Rear brake pipe union nut | 16 | – |
| Rear brake pipe clamp bolt | 9.0 | – |
Transfer case & driveshafts
Source: Ch. 12 Drive shafts & transfer box (12•187 – 12•198)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Driveshaft flange bolt (shafts No. 1, No. 2 and No. 3, rear diff side) | 50 | – |
| Driveshaft mounting bolt (transfer case side) | 33 | – |
| Transfer case plugs (filler, drain, level/filler) | 23 | Apply sealant to the threads. |
| 4WD switch | 19 | – |
| Switch protector bolt | 9 | – |
| Low-range (4L) switch | 21 | – |
| Transfer case housing bolts (long and short) | 18 | – |
| Transfer case flange nuts | 130 | Use a new nut. |
| Transfer case support mounting nut | 30 | – |
| Transfer case support bracket bolt | 23 | – |
Suspension
Source: Ch. 13 Chassis, appendix (13•220)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Front anti-roll bar nut | 50 | – |
| Anti-roll bar mounting bracket bolt | 23 | – |
| Front shock absorber lower nut | 60 | – |
| Front shock absorber upper nut | 35 | – |
| Front lateral rod (panhard) bolt to axle | 160 | – |
| Front lateral rod (panhard) bolt to body | 160 | – |
| Front trailing arm bolt | 95 | – |
| Front trailing arm rear nut | 73 | Final tighten after lowering the vehicle. |
| Rear lateral rod (panhard) bolt No. 1 | 95 | – |
| Rear lateral rod (panhard) nut | 95 | – |
| Rear shock absorber lower nut | 45 | – |
| Rear shock absorber upper bolt | 70 | Use a new bolt. |
| Rear bump stop (travel limiter) | 50 | – |
| Parking brake cable clamp bolt | 21 | – |
| Rear trailing arm nut No. 2 | 95 | – |
| Rear trailing arm nut No. 1 | 73 | Final tighten after lowering the vehicle. |
Brakes
Source: Ch. 14 Brake system (14•222 – 14•250)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Front caliper bleeder valve | 11 | Shown as 11 Nm on the components diagram. The caliper overhaul step lists 8.3 Nm. |
| Front caliper guide pin bolts | 22 | – |
| Front brake disc dust guard bolt | 50 | – |
| Front caliper mounting bracket bolts | 85 | – |
| Front brake hose union bolt | 23 | – |
| Rear wheel cylinder bleeder valve | 7.4 | – |
| Rear wheel cylinder mounting bolts | 8.9 | – |
| Rear brake pipe union nut | 16 | – |
| Brake pedal assembly nuts | 13 | Tighten in the sequence shown (1–3).
Show tightening order |
| Brake master cylinder nuts | 18 | – |
| Parking brake cable clamp bolts | 21 | – |
| Parking brake lever bolts | 23 | – |
| Parking brake mounting bracket bolts | 26 | – |
| ABS/ESP unit brake pipe union nuts (M10) | 16 | – |
| ABS/ESP unit brake pipe union nuts (M12) | 21 | – |
| ABS/ESP actuator support bolts | 5.4 | – |
| ABS/ESP actuator mounting bracket bolt | 21 | – |
| Front wheel speed sensor bolts | 8.8 | – |
| Rear wheel speed sensor screws | 8.8 | – |
Steering
Source: Ch. 15 Steering, appendix (15•262 – 15•269)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Steering wheel nut | 32 | – |
| Lower steering column nuts | 25 | – |
| Upper steering column nuts | 25 | – |
| Steering column bolt | 14 | – |
| Steering column nut | 14 | – |
| Steering shaft upper joint bolt | 35 | Tighten in the sequence shown.
Show tightening order |
| Steering shaft lower joint bolt | 35 | Tighten in the sequence shown.
Show tightening order |
| Steering shaft seal nuts | 15 | – |
| Tie rod end nut | 43 | – |
| Tie rod end lock nut | 65 | – |
| Front (drag link) tie rod end nut | 43 | – |
| Front (drag link) tie rod end lock nut | 65 | – |
| Steering damper mounting bolt | 50 | – |
| Steering damper end nut | 43 | – |
| Steering gear mounting nuts | 64 | – |
| Steering gear bolt No. 3 | 64 | – |
| Pitman arm nut | 128 | – |
| Steering gear adjusting screw lock nut | 37 | Clean the nut and apply sealant (SUZUKI Bond No. 1215) to the contact surface. |
Body & interior
Source: Ch. 16 Body (16•272 – 16•310)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Front bumper lower bolts | 9 | – |
| Rear bumper mounting bolts | 8.8 | Tighten in the sequence shown.
Show tightening order |
| Side panel mounting bolt | 9 | – |
| Bonnet latch bolts | 10 | Tighten in the sequence shown.
Show tightening order |
| Door hinge bolts | 23 | Tighten in the sequence shown.
Show tightening order |
| Door check strap (stroke limiter) bolt | 21 | – |
| Door lock striker bracket screw | 28 | – |
| Instrument panel support bolts | 23 | Tighten in the sequence shown.
Show tightening order |
| Front seat mounting bolts | 23 | Tighten in the sequence shown.
Show tightening order |
| Seatback-to-seat arm bolts | 50 | Tighten in the sequence shown.
Show tightening order |
| Rear seat backrest bolts | 43 | Tighten in the sequence shown.
Show tightening order |
Heating & air conditioning
Source: Ch. 17 Heating, ventilation & A/C, appendix (17•346)
| Component | Torque (Nm) | Notes |
|---|---|---|
| A/C condenser bolts | 10 | Tighten in the sequence shown.
Show tightening order |
| Drain hose bolt | 10 | – |
| Liquid line pipe bolt | 10 | – |
| Suction line hose bolt | 10 | – |
| HVAC module bolt | 10 | – |
| A/C module nut (engine bay side) | 10 | – |
| A/C module nut (cabin side) | 4.5 | – |
| Expansion valve mounting bolt | 7.0 | – |
| Suction pipe mounting bolt | 10 | – |
| Refrigerant pressure sensor | 11 | – |
| A/C compressor bolt | 25 | Tighten in the sequence shown.
Show tightening order |
| Plate fixing bolt | 18 | – |
| Pressure relief valve | 10 | – |
Airbags (SRS)
Source: Ch. 18 Passive safety (18•352 – 18•354)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Contact coil (clock spring) bolts | 15 | Make sure the front wheels are pointing straight ahead. |
| Front airbag module bolts | 23 | – |
| Impact sensor bolt | 9 | – |
Engine electrical
Source: Ch. 19A Engine electrical (19A•358 – 19A•375)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Spark plugs | 25 | – |
| Alternator bolt | 25 | – |
| Alternator adjusting bolt | 5 | – |
| Alternator lower bolt | 48 | On refit, first tighten to 30 Nm to close the bushing gap, then final-tighten. |
| Alternator B-terminal nut | 8 | – |
| Alternator pulley nut | 130 | – |
| Alternator stator bolts | 6 | – |
| Alternator rear cover bolts | 4.5 | – |
| Alternator bearing retainer screws | 2.3 | – |
| Alternator brush holder screws | 2 | – |
| Starter-to-engine bolts | 56 | – |
| Starter wire nut | 11 | – |
| Starter through (tie) bolts | 3.0 | – |
| Starter solenoid bolts | 3.0 | – |
Wipers & body electrical
Source: Ch. 19B Electrical equipment (19B•378 – 19B•382)
| Component | Torque (Nm) | Notes |
|---|---|---|
| Antenna mounting bolt | 7.0 | – |
| Washer reservoir bolts | 8.4 | Tighten in the sequence shown.
Show tightening order |
| Front wiper motor bolts | 8.3 | Tighten in the sequence shown.
Show tightening order |
| Front wiper arm nuts | 18 | – |
| Rear wiper motor bolts | 8.3 | Tighten in the sequence shown.
Show tightening order |
| Rear wiper arm nut | 7.9 | – |